Publikationer

Din avgränsning ger 21 träffar.

• 2017:32 COMRAD – Comprehensive investigation of the performance of computed and digital radiography

  Background Within the industry, there has long been a need to replace the traditional X-ray film and its handling. These both for economic and environmental considerations. Both computed radiography and digital radiography offer many advantages over the traditional use of x-ray with film. However, the transition from film-based radiography requires in-depth knowledge of the relationship...

  Innehållstyp: Publikationer

• 2017:29 Evaluation of the simulation software CIVA for qualification purpose

  Background Modeling is an important tool within NDT, partly to develop and optimize testing technologies, but also within the Qualification Body’s activities to assess technical verifications and perform parameter studies. SSM has supported university research in the area for many years and, among other things, in the development of a software for ultrasound modeling. In addition, the...

  Innehållstyp: Publikationer

• 2017:27 Översyn av beredskapszoner

  Sammanfattning Den 22 oktober 2015 gav regeringen Strålsäkerhetsmyndigheten (SSM) i uppdrag att, i samråd med Myndigheten för samhällsskydd och beredskap (MSB), berörda länsstyrelser samt andra berörda myndigheter och aktörer, genomföra en översyn av de beredskapszoner som gäller för verksamheter med joniserande strålning. SSM...

  Innehållstyp: Publikationer

• 2017:25 Evaluation of weld fatigue reduction in austenitic stainless steel pipe components

  Background The performed investigation is a continuation of the work performed in SSM 2015:38 where fatigue tests were performed on pressurized welded austenitic stainless steel piping components. The specimens were subjected to a realistic variable amplitude loading with mainly reversed bending deformation and particular focus on high cycle fatigue. The previous fatigue results were quite...

  Innehållstyp: Publikationer

• 2017:23 Kalibrering för bestämning av optimal beräkningsmodell

  Bakgrund SSM bedömer i tillsynen avancerade datorberäkningar relaterade till drift av kärnkraftverk, utförda av extern part. Inom kärnkraft kan experimentella undersökningar vara olämpliga. Beräkningar blir därför ofta det enda alternativet att undersöka möjliga konsekvenser av planerade förändringar. Beräkningsmodeller...

  Innehållstyp: Publikationer

• 2017:22 Effect of weld repairs on residual stresses in nickel base dissimilar metal welds

  Background The driving force for crack growth near welds in nuclear application piping may arise from weld residual stresses. Experience from nondestructive examination show that cracks in dissimilar metal welds are often found near weld repairs. The repair welding may affect the residual stresses through e.g. increased tensile stresses and increased plastic straining on the surfaces of the...

  Innehållstyp: Publikationer

• 2017:20 Assessment of inertia effects on transient clad-to-coolant heat transfer and coolant flow under reactivity initiated accidents

  In this report, simple hydrodynamic models are used for studying the effects of coolant inertia on fuel-to-coolant heat transfer and coolant flow under reactivity initiated accidents in light water reactors. The objective is to assess if the inertia effects are important enough to warrant modification of QT-COOL, a coolant channel module for two-phase flow that has recently been implemented as...

  Innehållstyp: Publikationer

• 2017:19 Numerical simulations of headed anchors break in reinforced and non-reinforced concrete structures, Phase 2

  Background In the design of anchorage equipment in concrete structures the beneficial effects of reinforcement are, in most cases, not considered. The American ASCI 349-06 code opens up for a more detailed analysis where the beneficial impact of reinforcement on anchor capacity can be taken into account. How this analysis can be done is, however, not explicitly described in the code. The...

  Innehållstyp: Publikationer

• 2017:16 Stress intensity factor solutions for circumferential cracks in cylindrical bars under axisymmetric loading and global bending

  Background The case of a circumferential crack in a cylindrical bar has not been available in the ProSACC code. The need for such a geometry, especially considering nonlinear axisymmetric loading and global bending, has motivated the development of new stress intensity factor solutions, also known as K-solutions. These new K-solutions will be available in ISAAC, the successor to ProSACC.

  Innehållstyp: Publikationer

• 2017:11 Extended Common Load Model: A tool for dependent failure modelling in highly redundant structures

  Background The treatment of dependent failures is one of the most controversial subjects in reliability and risk analyses. The difficulties are specially underlined in the case of highly redundant systems, when the number of redundant components or trains exceeds four. The Common Load Model (CLM), originally defined in the 70’ies, differs from other CCF models, as it relies on a specific...

  Innehållstyp: Publikationer