Din avgränsning ger 122 träffar.
-
2010:45 Evaluation of models for cyclic plastic deformation – A literature study
Analysis of nuclear components subjected to cyclic plastic deformation is normally based on the American standard ASME III. With the focus to improve the modeling of the stress-strain response under non-monotonic loading, several models for the analysis of cyclic plastic deformation have been developed in recent years. However, experience shows that the analysis and evaluation of plastic...
Innehållstyp: Publikationer -
2010:42 Using the EPRI Risk-Informed ISI Methodology on Piping Systems in Forsmark 3
In the SSM regulation SSMFS 2008:13, it is stated that the selection of locations for inspection of mechanical components shall be based upon the risk for core damage or the risk of release of radioactive substances. Both qualitative and quantitative measures of the relative risk are allowed to be used. So far only the PWRs in Sweden are using a quantitative procedure to evaluate the risk...
Innehållstyp: Publikationer -
2010:16 Guidance to Risk-Informed Evaluation of Technical Specifications using PSA
No guidance documents for risk-informed analysis and assessment of changes in Limiting Conditions for Operation (LCO:s) in TS (Technical Specifications) have been available in the Nordic countries. In the U.S. several guidance documents, primarily developed by the owners groups for PWRs and BWRs, exist. Guidance for analysis of TS changes in this report generally follows the U.S. Regulatory...
Innehållstyp: Publikationer -
2010:07 Indicators of safety culture – selection and utilization of leading safety performance indicators
Safety indicators play a role in providing information on organizational performance, motivating people to work on safety and increasing organizational potential for safety. The aim of this report is to provide an overview on leading safety indicators in the domain of nuclear safety. The report explains the distinction between lead and lag indicators and proposes a framework of three types of...
Innehållstyp: Publikationer -
2009:38 Research and Development Program in Reactor Diagnostics and Monitoring with Neutron Noise Methods, Stages 14 and 15
This report constitutes Stages 14 and 15 of a long-term research and development program concerning the development of diagnostics and monitoring methods for nuclear reactors. Stage 14 was a full one-year project, whereas Stage 15 consisted of a half-year project. Results up to Stage 13 were reported in SKI reports, as listed below and in the Summary. The results have also been published in...
Innehållstyp: Publikationer -
2009:27 Analysis Strategy for Fracture Assessment of Defects in Ductile Materials
SSM has supported research for investigating the role of secondary stresses when fracture assessments are performed for cracked structures made of ductile materials. There are evidences that indicate that some secondary stresses, such as weld residual stresses, are not as important as primary stresses for estimating the safety margin against rupture (measured by the J-integral) for the type...
Innehållstyp: Publikationer -
2009:17 Effect of Welding Residual Stresses on Crack Opening Displacement and Crack-Tip Parameters
Weld residual stresses have a large influence on the behavior of cracks growing under normal operation loads and on the leakage-flow from a through-wall crack. Accurate prediction of these events is important in order to arrive at proper conclusions when assessing detected flaws, for inspection planning and for assessment of leak-before-break margins. The fracture mechanical treatment of weld...
Innehållstyp: Publikationer -
2009:16 Influence of Hardening Model on Weld Residual Stress Distribution
Weld residual stresses have a large influence on the behavior of cracks growing under normal operation loads and on the leakage-flow from a through-wall crack. Accurate prediction of these events is important in order to arrive at proper conclusions when assessing detected flaws, for inspection planning and for assessment of leak-before-break margins. Therefore, it is very important to have...
Innehållstyp: Publikationer -
2009:15 Improvement and Validation of Weld Residual Stress Modelling Procedure
Weld residual stresses have a large influence on the behavior of cracks growing under normal operation loads and on the leakage-flow from a through-wall crack. Accurate prediction of these events is important in order to arrive at proper conclusions when assessing detected flaws, for inspection planning and for assessment of leak-before-break margins. Therefore, it is very important to have...
Innehållstyp: Publikationer -
2009:12 Evaluating safety-critical organizations – emphasis on the nuclear industry
The regulator identified a few years ago a need for a better understanding of and a deeper knowledge on methods for evaluating safety critical organisations. There is a need for solid assessment methods in the process of management of organisational changes as well as in continuously performed assessment of organisations such as nuclear power plants. A considerable body of literature exists...
Innehållstyp: Publikationer