Filtered generated 248 hits.
-
2014:28 Numerical simulation of ductile crack growth in residual stress fields
The study has shown on the capability of the cell model in capturing the effects on ductile tearing from limited pre-load levels and a residual stress field. Some of the conclusions are as follows: No distinctive influence on the material fracture toughness is observed from pre-loading (work hardening), both tensile and compressive, at room temperature of 1.5 or 3 % total strain. The cell...
Content type: Publications -
2014:27 Regulation applying to welding of pressure equipment – a comparative study
The PED was in force in November 1999 and has been mandatory in European Union Member States since May 2002. Most of the standards referred to in the PED are relatively new although some of the standards were adopted in the early 1990s. On the other hand, the ASME B&PV Code has been used for a long time now and is the result of several decades of industrial experiences. The authors present...
Content type: Publications -
2014:21 Effects of additives on uranium dioxide fuel behavior
This report will form a basis for the reviews that SSM does when the license holders applies for use of nuclear fuel with additives. The report is also intended as a reference to the models that Quantum Technologies AB has developed. The report and the models will be a valuable source of information for SSM and other parties when discussing the performance of doped fuel. Ali Massih SSM...
Content type: Publications -
2014:20 An evaluation of high-temperature creep of zirconium alloys: data versus models
In this report Dr Massih presents correlations for creep in different phases of zirconium alloys and also presents a general solution to the difficulty of accurately describing the material properties in phase transition for several zirconium alloys. Based upon superplasticity relations, models are adapted to fit with experimental data for materials in transition regions. The creep models are...
Content type: Publications -
2014:19 Evaluation of the Halden IFA-650 loss-of-coolant accident experiments 5, 6 and 7
The analytical tools, which are fuel rod computer codes, that Quantum Technologies AB use and develop, contain models of several of the phenomena that are acting on the nuclear fuel (cladding temperature, fission gas driven pressure, strain and stress in the cladding, rod rupture, etc.) and how the separate effects interact in the complex integrated manner. The codes are under constant...
Content type: Publications -
2014:18 Evaluation of the Halden IFA-650 loss-of-coolant accident experiments 2, 3 and 4
The analytical tools, which are fuel rod computer codes, that Quantum Technologies AB use and develop, contain models of several of the phenomena that are acting on the nuclear fuel (cladding temperature, fission gas driven pressure, strain and stress in the cladding, rod rupture, etc.) and how the separate effects interact in the complex integrated manner. The codes are under constant...
Content type: Publications -
2014:09 Further Development of the Core Simulator CORE SIM: Extension to coupled capabilities for BWRs
The developed tool is fully MatLab based and requires a set of input data from a commercial static core simulator. The driving perturbation can be specified both as a perturbation in thermo-hydraulic parameters or directly as a perturbation in macroscopic cross-sections. As output, the 3-dimensional spatial distribution of the noise in coolant density, pressure, enthalpy, inlet velocity, fuel...
Content type: Publications -
2014:01 Cost Estimating for Decommissioning Nuclear Reactors in Sweden
In Sweden, decommissioning cost estimates are core inputs to the process of calculating licensee contributions to the Swedish national fund for radioactive waste management and decommissioning. Under the present system, the decommissioning cost estimates are produced by licensees every three years and formally submitted to the Swedish Radiation Safety Authority (SSM), which reviews the...
Content type: Publications -
2013:29 Regulatory Approaches in Nuclear Power Supervision
The objective of this follow-up study was to support SSM in further understanding regulatory approaches and how they can be combined as part of effective strategies. The survey was intended to assist SSM in identifying current standards, experiences, and practices in the regulation of nuclear power plants. The results will also be valuable for the participating authorities as well as other...
Content type: Publications -
2013:27 Numerical simulations of headed anchors break in reinforced and non-reinforced concrete structures
The design codes for anchorage of equipment in concrete structures have been developed since the time the Swedish power plants were designed. Furthermore, the design basis has been updated and in some cases new mechanical loads have been added. As a consequence, it can be difficult for some anchorages to meet the requirements of today. In the design of anchorage equipment the beneficial effect...
Content type: Publications