Filtered generated 17 hits.
-
2017:32 COMRAD – Comprehensive investigation of the performance of computed and digital radiography
Background Within the industry, there has long been a need to replace the traditional X-ray film and its handling. These both for economic and environmental considerations. Both computed radiography and digital radiography offer many advantages over the traditional use of x-ray with film. However, the transition from film-based radiography requires in-depth knowledge of the relationship...
Content type: Publications -
2017:29 Evaluation of the simulation software CIVA for qualification purpose
Background Modeling is an important tool within NDT, partly to develop and optimize testing technologies, but also within the Qualification Body’s activities to assess technical verifications and perform parameter studies. SSM has supported university research in the area for many years and, among other things, in the development of a software for ultrasound modeling. In addition, the...
Content type: Publications -
2017:25 Evaluation of weld fatigue reduction in austenitic stainless steel pipe components
Background The performed investigation is a continuation of the work performed in SSM 2015:38 where fatigue tests were performed on pressurized welded austenitic stainless steel piping components. The specimens were subjected to a realistic variable amplitude loading with mainly reversed bending deformation and particular focus on high cycle fatigue. The previous fatigue results were quite...
Content type: Publications -
2017:22 Effect of weld repairs on residual stresses in nickel base dissimilar metal welds
Background The driving force for crack growth near welds in nuclear application piping may arise from weld residual stresses. Experience from nondestructive examination show that cracks in dissimilar metal welds are often found near weld repairs. The repair welding may affect the residual stresses through e.g. increased tensile stresses and increased plastic straining on the surfaces of the...
Content type: Publications -
2017:20 Assessment of inertia effects on transient clad-to-coolant heat transfer and coolant flow under reactivity initiated accidents
In this report, simple hydrodynamic models are used for studying the effects of coolant inertia on fuel-to-coolant heat transfer and coolant flow under reactivity initiated accidents in light water reactors. The objective is to assess if the inertia effects are important enough to warrant modification of QT-COOL, a coolant channel module for two-phase flow that has recently been implemented as...
Content type: Publications -
2017:19 Numerical simulations of headed anchors break in reinforced and non-reinforced concrete structures, Phase 2
Background In the design of anchorage equipment in concrete structures the beneficial effects of reinforcement are, in most cases, not considered. The American ASCI 349-06 code opens up for a more detailed analysis where the beneficial impact of reinforcement on anchor capacity can be taken into account. How this analysis can be done is, however, not explicitly described in the code. The...
Content type: Publications -
2017:18 FEM analysis of the mechanical integrity for the canister intended for storage of spent nuclear fuel with regard to copper creep ductility
Background For final storage of spent nuclear fuel it is suggested by the Swedish nuclear fuel and waste management company (SKB) to emplace the nuclear fuel into copper canisters which are surrounded by bentonite clay at approximately 500 meters’ depth into granitic rock. After emplacement of the canisters Bentonite swelling due to water saturation and hydrostatic pressure build up the...
Content type: Publications -
2017:16 Stress intensity factor solutions for circumferential cracks in cylindrical bars under axisymmetric loading and global bending
Background The case of a circumferential crack in a cylindrical bar has not been available in the ProSACC code. The need for such a geometry, especially considering nonlinear axisymmetric loading and global bending, has motivated the development of new stress intensity factor solutions, also known as K-solutions. These new K-solutions will be available in ISAAC, the successor to ProSACC.
Content type: Publications -
2017:15 Radionuclide release rates associated with bounding cases featuring relatively early canister failures in a spent fuel repository
Background In 2011 the Swedish Nuclear Fuel and Waste Management Co (SKB) submitted a license application for construction of a geological repository for spent nuclear fuel according to the KBS-3 method, comprising of copper canisters, bentonite buffer, backfill and surrounding crystalline bedrock. The post-closure safety assessment of the repository, SR-Site, has been reviewed by the Swedish...
Content type: Publications -
2017:13 Monte Carlo patient-specific pre-treatment QA system for volumetric modulated arc therapy
Background The clinical use of volumetric modulated arc therapy (VMAT) has augmented rapidly since it became commercially available. As a result, the need for comprehensive quality assurance (QA) has increased. Current practices in Sweden normally compare the delivered dose with the planned dose based on measurements with different methods, for instance: portal dosimetry, point dose...
Content type: Publications