Filtered generated 211 hits.
-
2011:16 Modelling of ultrasonic testing of cracks in cladding
During the last two decades, SSM has supported research to develop a model for the non-destructive test situation based on ultrasonic technique. Such a model is important in many ways, for example to supplement and plan experimental studies and to perform parametric studies in qualification situation. Modeling can be a useful tool when the inspection system shall be technically justified.
Content type: Publications -
2011:13 Investigation of Discrete-Fracture Network Conceptual Model Uncertainty at Forsmark
Flow modelling using alternative assumptions regarding conceptual and parametric uncertainty in the spatial and structural relationships among fractures indicates elevated flow rates and groundwater velocities to deposition holes compared to SKB’s flow modelling results. Simulated sampling of fractures in boreholes does not indicate any reason to exclude the proposed spatial and structural...
Content type: Publications -
2011:12 Analysis of Barrier Performance: Modelling of Copper corrosion scenarios with and without buffer erosion
The purpose of this project was to develop a numerical modelling capacity to address the corrosion of the copper canister under gradually changing transport conditions caused by buffer erosion and removal of buffer mass. Due to the complexity of this task, such a model cannot be realistic in all respects, but the present effort should address the feasibility of solving numerical and...
Content type: Publications -
2011:11 Handling Interfaces and Time-varying Properties in Radionuclide Transport Models
Quintessa’s QPAC code has been used to investigate the Qeq approach. The conclusions from this simulation study are the following. The basic approach to calculating Qeq values is sound, however, narrow channels could lead to the same release as larger fractures with the same pore velocity, so a channel enhancement factor of √10 should be considered. A spalling zone that increases the area of...
Content type: Publications -
2011:09 Is Copper Immune to Corrosion When in Contact With Water and Aqueous Solutions?
The KBS-3concept implies that spent nuclear fuel is placed in copper canisters surrounded by clay and finally placed approximately 500 m down from surface into granitic bedrock, in order to isolate the spent nuclear fuel from humans and environment for very long time scales (i.e. millions of years). The concept is based on the multi-barrier principle, in this respect the barriers are the...
Content type: Publications -
2011:08 Workshop on Copper Corrosion and Buffer Erosion Stockholm 15-17 September 2010
In SSM:s preparation for reviewing SKB:s license application for disposal of spent nuclear fuel, a series of technical workshops have been conducted. The main purpose of this type of workshops is to get an overall understanding of the state of knowledge on interdisciplinary issues as well as of questions in the research front by inviting several experts. Previous workshops have addressed the...
Content type: Publications -
2011:07 Workshop on Regulatory Review and Safety Assessment Issues in Repository Licensing
The Swedish Radiation safety Authority (SSM) is currently developing project plans for the review of the Swedish Nuclear Fuel and Waste Management Co’s (SKB) planned license application for a spent nuclear fuel repository in Forsmark and an encapsulation plant in Oskarshamn. In support of the development of these project plans, SSM has carried out several international workshops during 2010...
Content type: Publications -
2009:29e Swedish national plan for the management of all radioactive waste
The Swedish Radiation Safety Authority has been assigned by the government to develop a national plan for the management of all radioactive waste. This report was presented to the government 30 June 2009. The report has been developed in coordination with representatives from other authorities, trade and industry organizations, operators and other parties interested, forming a joint action...
Content type: Publications -
2010:43 Displacement along extensive deformation zones at the two SKB sites: Forsmark and Laxemar
The Fennoscandian shield is distinguished by that the exposed bedrock is mainly composed of Precambrian metamorphic and igneous rocks older than a billion or one and a half billion years with few easily distinguished testimonies for the younger history. Large parts of the present ground surface closely coincides with a late Precambrian denudation surface; the sub-Cambrian peneplain.
Content type: Publications -
2010:41 Rock-block configuration in Uppland and the Ålands-hav basin, the regional surroundings of the SKB site in Forsmark, Sea and land areas, eastern Sweden
This report concerns a study which was initially conducted for the Swedish Nuclear Power Inspectorate (SKI), which is now merged into the Swedish Radiation Safety Authority (SSM). The conclusions and viewpoints presented in the report are those of the authors and do not necessarily coincide with those of the SSM. The topography in Uppland is more broken in the sea area east and northeast of...
Content type: Publications