Filtered generated 278 hits.
-
2011:04 Evaluation of the Technical Basis for New Proposals of Fatigue Design of Nuclear Components
During the recent years fatigue analysis procedures for nuclear components have been investigated. The most common method so far has been the American code ASME III. The basis for the current design procedures in ASME III is quite old and has now been evaluated against modern data leading to the proposal of modified design curves. Also the effect of the environment has been the subject of...
Content type: Publications -
2005:60 Research and Service Experience with Environmentally-Assisted Cracking in Carbon and Low-Alloy Steels in High-Temperature Water
In this report, the most relevant aspects of research and service experience with environmentally assisted cracking of carbon and low-alloy steels in high-temperature water are reviewed, with special emphasis on the primary pressure-boundary components of boiling water reactors. The main factors controlling the susceptibility to environmentally assisted cracking under light water reactor...
Content type: Publications -
2001:23 Interactions of Severe Accident Researchand Regulatory Positions (ISARRP)
This project, started on April 1, 1999, had the specific objectives of determining whether; (i) the focus of the severe accidents (SA) research is consistent with that of the regulatory authorities, (ii) the results obtained so far by SA research satisfy the regulatory concerns, (iii) the future programs, envisaged will address the potential regulatory needs into next century, and (iv) how...
Content type: Publications -
2002:04 Qualification of Electrical Components in Nuclear Power Plants. Management of Ageing
The work was finished and reported in Swedish in a limited publication 2000, Ingemansson Rapport H-14061-r-I. As the performed work was regarded to be of more general interest it is published again as a research report by the Swedish Nuclear Power Inspectorate. To be used in the international cooperation in nuclear safety it was also translated into English by the inspectorate, which is this...
Content type: Publications -
2007:05 Development of an Input Model to MELCOR 1.8.5 for Oskarshamn 3 BWR
200 Lars Nilsson SKI English...
Content type: Publications -
2022:18 Data report – sampling of sea water and marine organisms outside Ringhals NPP
SSM perspective Background The Radiation Safety Authority (SSM) funded the collection of marine biota over an annual cycle at the Ringhals nuclear power plant (NPP) to enable development of analytical methods for C-14. Methods for the C-14 analysis and results in the form of levels of C-14 in various marine organisms have been reported by the Swedish Defense Research Institute (FOI) in FOI...
Content type: Publications -
2022:04 Warm Pre-Stressing mechanisms
SSM perspective Background Swedish nuclear power plants (NPP) were originally designed and analyzed with an assumed operating period of approximately 40 years. As Swedish NPPs reach their original technical design life the safety of the additional operating time has to be verified. With increased operating time, the shift in the fracture toughness curve of the reactor pressure vessel (RPV)...
Content type: Publications -
2022:09 Assessment of modelling approaches for axial gas flow inside LWR fuel rods
SSM perspective Background The fuel rod analysis program SCANAIR has been developed by IRSN (Institut de Radioprotection et de Sûreté Nucléaire) for analysis of reactivity initiated accidents (RIA) in light water reactors. The Swedish Radiation Safety Authority (SSM) has access to SCANAIR in exchange for annual contributions for its further development. The development and administration...
Content type: Publications -
2022:11 Kingdom of Sweden IRRS ARM Summary Report 2022
The IAEA Integrated Regulatory Review Service Mission to Sweden in November 2022...
Content type: Publications -
2022:14 Weld residual stress and strain measurements on a mock-up with single layer strip cladding common in reactor pressure vessels
Summary Residual stress and strain measurements were performed on a mock-up consisting of a 160 mm thick low-alloy ferritic steel plate of type SA-508 Class 3 with a single layer weld deposited strip cladding of austenitic stainless steel E308L. The cladding was manufactured with submerged arc strip welding adapted to a procedure used for reactor pressure vessels in the 1970s. Comprehensive...
Content type: Publications