Filtered generated 216 hits.
-
2021:10 Establishment and use of attention values in environmental fatigue assessments
SSM perspective Background As Swedish NPPs reach their original technical design life, re-assessment of the fatigue life of structural components is needed for safe long term operation (LTO). In these re-assessments one must consider that new knowledge has shown that environmental effects on fatigue life must be considered. One common method to verify the fatigue life of structural components...
Content type: Publications -
2021:20 Effects of additives on UO2 fuel behavior: expanded edition
SSM perspective Background The Swedish Radiation Safety Authority (SSM) follows the development of nuclear fuel closely. Fuel with additives like chromia and gadolinia is used in Swedish reactors and fuel with even better thermal and mechanical properties is under development. This project is an in-depth study of data and models regarding the impact of additives on the properties of uranium...
Content type: Publications -
2022:18 Data report – sampling of sea water and marine organisms outside Ringhals NPP
SSM perspective Background The Radiation Safety Authority (SSM) funded the collection of marine biota over an annual cycle at the Ringhals nuclear power plant (NPP) to enable development of analytical methods for C-14. Methods for the C-14 analysis and results in the form of levels of C-14 in various marine organisms have been reported by the Swedish Defense Research Institute (FOI) in FOI...
Content type: Publications -
2022:04 Warm Pre-Stressing mechanisms
SSM perspective Background Swedish nuclear power plants (NPP) were originally designed and analyzed with an assumed operating period of approximately 40 years. As Swedish NPPs reach their original technical design life the safety of the additional operating time has to be verified. With increased operating time, the shift in the fracture toughness curve of the reactor pressure vessel (RPV)...
Content type: Publications -
2022:09 Assessment of modelling approaches for axial gas flow inside LWR fuel rods
SSM perspective Background The fuel rod analysis program SCANAIR has been developed by IRSN (Institut de Radioprotection et de Sûreté Nucléaire) for analysis of reactivity initiated accidents (RIA) in light water reactors. The Swedish Radiation Safety Authority (SSM) has access to SCANAIR in exchange for annual contributions for its further development. The development and administration...
Content type: Publications -
2022:11 Kingdom of Sweden IRRS ARM Summary Report 2022
The IAEA Integrated Regulatory Review Service Mission to Sweden in November 2022...
Content type: Publications -
2022:14 Weld residual stress and strain measurements on a mock-up with single layer strip cladding common in reactor pressure vessels
Summary Residual stress and strain measurements were performed on a mock-up consisting of a 160 mm thick low-alloy ferritic steel plate of type SA-508 Class 3 with a single layer weld deposited strip cladding of austenitic stainless steel E308L. The cladding was manufactured with submerged arc strip welding adapted to a procedure used for reactor pressure vessels in the 1970s. Comprehensive...
Content type: Publications -
2017:19 Numerical simulations of headed anchors break in reinforced and non-reinforced concrete structures, Phase 2
Background In the design of anchorage equipment in concrete structures the beneficial effects of reinforcement are, in most cases, not considered. The American ASCI 349-06 code opens up for a more detailed analysis where the beneficial impact of reinforcement on anchor capacity can be taken into account. How this analysis can be done is, however, not explicitly described in the code. The...
Content type: Publications -
2017:11 Extended Common Load Model: A tool for dependent failure modelling in highly redundant structures
Background The treatment of dependent failures is one of the most controversial subjects in reliability and risk analyses. The difficulties are specially underlined in the case of highly redundant systems, when the number of redundant components or trains exceeds four. The Common Load Model (CLM), originally defined in the 70’ies, differs from other CCF models, as it relies on a specific...
Content type: Publications -
2017:25 Evaluation of weld fatigue reduction in austenitic stainless steel pipe components
Background The performed investigation is a continuation of the work performed in SSM 2015:38 where fatigue tests were performed on pressurized welded austenitic stainless steel piping components. The specimens were subjected to a realistic variable amplitude loading with mainly reversed bending deformation and particular focus on high cycle fatigue. The previous fatigue results were quite...
Content type: Publications