Filtered generated 217 hits.
-
2020:16 Estimates ofJ-integral and COD for circumferential through wall cracks under global bending including the effect of pipe end restraint
SSM perspective Background Leak-before-break (LBB) piping assessments have shown that piping systems can withstand long through-wall cracks before pipe rupture is expected. This is somewhat because pipe ends are restrained. In LBB assessments analyses are often performed for a pipe segment uncoupled from the piping system, as pipe ends are assumed unrestrained. This assumption is conservative...
Content type: Publications -
2020:02 Models for axial gas flow and mixing in LWR fuel rods
SSM perspective Background Fission gases inside a fuel rod plays an important role in the behaviour of the fuel, both during normal operation and during events and accidents. Fission gases are released from inside the fuel pellets to the gap between the pellet and the cladding tube and then flow to the plenum volume at the top of the fuel rod. In high burnup fuel, this axial flow to the...
Content type: Publications -
2012:02 Evaluation of activity build-up experiments
This project aims to understand how the water chemistry affects the activity build-up on surfaces in different systems in Swedish nuclear power plants, which in turn provides information on conditions required to reduce the radiation exposure to power plant staff. The study was done to obtain knowledge about water chemistry conditions preferred to minimize the activity build-up. A number of...
Content type: Publications -
2007:05 Development of an Input Model to MELCOR 1.8.5 for Oskarshamn 3 BWR
200 Lars Nilsson SKI English...
Content type: Publications -
2005:60 Research and Service Experience with Environmentally-Assisted Cracking in Carbon and Low-Alloy Steels in High-Temperature Water
In this report, the most relevant aspects of research and service experience with environmentally assisted cracking of carbon and low-alloy steels in high-temperature water are reviewed, with special emphasis on the primary pressure-boundary components of boiling water reactors. The main factors controlling the susceptibility to environmentally assisted cracking under light water reactor...
Content type: Publications -
2001:23 Interactions of Severe Accident Researchand Regulatory Positions (ISARRP)
This project, started on April 1, 1999, had the specific objectives of determining whether; (i) the focus of the severe accidents (SA) research is consistent with that of the regulatory authorities, (ii) the results obtained so far by SA research satisfy the regulatory concerns, (iii) the future programs, envisaged will address the potential regulatory needs into next century, and (iv) how...
Content type: Publications -
2002:04 Qualification of Electrical Components in Nuclear Power Plants. Management of Ageing
The work was finished and reported in Swedish in a limited publication 2000, Ingemansson Rapport H-14061-r-I. As the performed work was regarded to be of more general interest it is published again as a research report by the Swedish Nuclear Power Inspectorate. To be used in the international cooperation in nuclear safety it was also translated into English by the inspectorate, which is this...
Content type: Publications -
2021:04 Calibration of models for cladding tube high-temperature creep and rupture in the FRAPTRAN-QT-1.5 program
SSM perspective Background In Swedish Light Water Reactors (LWR), stress corrosion cracking of reactor components and welds occurs from time to time. As the nuclear power plants are ageing, it is essential to study and further understand the mechanism for environmentally induced sensitization. Natural cracking is a phenomenon that is difficult to predict and very hard to study since it occurs...
Content type: Publications -
2008:07 Modelling of long term geochemical evolution and study of mechanical perturbation of bentonite buffer of a KBS-3 repository
PART I: The Swedish Nuclear Fuel and Waste Management Co. (SKB) has recently completed a safety assessment project named SR-Can, related to the KBS-3 disposal concept. In this concept, the waste packages are surrounded by a buffer made of either MX-80 or Deponit CA-N bentonite. Interactions between the buffer and groundwater may modify the buffer composition and thus its containment...
Content type: Publications -
2021:09 Mechanisms important for material modelling in weld residual stress analysis
SSM perspective Background The prediction of weld residual stresses (WRS) is very complex as many mechanisms and phenomena influence the development of WRS during welding. For accurate prediction, the constitutive material models used are essential and must be able to describe the material response of the weldment constituents. For example, selection of a material model should only depend on...
Content type: Publications