Filtered generated 296 hits.
-
2009:17 Effect of Welding Residual Stresses on Crack Opening Displacement and Crack-Tip Parameters
Weld residual stresses have a large influence on the behavior of cracks growing under normal operation loads and on the leakage-flow from a through-wall crack. Accurate prediction of these events is important in order to arrive at proper conclusions when assessing detected flaws, for inspection planning and for assessment of leak-before-break margins. The fracture mechanical treatment of weld...
Content type: Publications -
2009:38 Research and Development Program in Reactor Diagnostics and Monitoring with Neutron Noise Methods, Stages 14 and 15
This report constitutes Stages 14 and 15 of a long-term research and development program concerning the development of diagnostics and monitoring methods for nuclear reactors. Stage 14 was a full one-year project, whereas Stage 15 consisted of a half-year project. Results up to Stage 13 were reported in SKI reports, as listed below and in the Summary. The results have also been published in...
Content type: Publications -
SSM Report 2008:01 A combined deterministic and probabilistic procedure for safety assessment of components with cracks – Handbook
SSM has supported research work for the further development of a previously developed procedure/handbook (SKI Report 99:49) for assessment of detected cracks and tolerance for defect analysis. During the operative use of the handbook it was identified needs to update the deterministic part of the procedure and to introduce a new probabilistic flaw evaluation procedure. Another identified need...
Content type: Publications -
2010:45 Evaluation of models for cyclic plastic deformation – A literature study
Analysis of nuclear components subjected to cyclic plastic deformation is normally based on the American standard ASME III. With the focus to improve the modeling of the stress-strain response under non-monotonic loading, several models for the analysis of cyclic plastic deformation have been developed in recent years. However, experience shows that the analysis and evaluation of plastic...
Content type: Publications -
2005:60 Research and Service Experience with Environmentally-Assisted Cracking in Carbon and Low-Alloy Steels in High-Temperature Water
In this report, the most relevant aspects of research and service experience with environmentally assisted cracking of carbon and low-alloy steels in high-temperature water are reviewed, with special emphasis on the primary pressure-boundary components of boiling water reactors. The main factors controlling the susceptibility to environmentally assisted cracking under light water reactor...
Content type: Publications -
2001:23 Interactions of Severe Accident Researchand Regulatory Positions (ISARRP)
This project, started on April 1, 1999, had the specific objectives of determining whether; (i) the focus of the severe accidents (SA) research is consistent with that of the regulatory authorities, (ii) the results obtained so far by SA research satisfy the regulatory concerns, (iii) the future programs, envisaged will address the potential regulatory needs into next century, and (iv) how...
Content type: Publications -
2002:04 Qualification of Electrical Components in Nuclear Power Plants. Management of Ageing
The work was finished and reported in Swedish in a limited publication 2000, Ingemansson Rapport H-14061-r-I. As the performed work was regarded to be of more general interest it is published again as a research report by the Swedish Nuclear Power Inspectorate. To be used in the international cooperation in nuclear safety it was also translated into English by the inspectorate, which is this...
Content type: Publications -
1996:70 Risks from Nuclear Waste
The first part of this review discusses the importance of risk. Man seems to have a longing for risks, like a part of the human nature. If risks are missing, they have to be invented, as needed parts in the emotional attraction of sports, amusement parks, traveling, etc.; this is the emotional part of risk. There is also a rational part of risk , in selecting such objects in ordinary life big...
Content type: Publications -
1995:70 Crack Characterisation for In-service
During in-service inspection by non destructive testing the reliability is highly dependent on how the equipment is adjusted to the specific object and to the anticipated crack features. The crack feature and morphology vary widely between different cracking mechanisms and between material types, in which the cracks appear. The major objective of this study was to characterise a number of...
Content type: Publications -
96:51 The Flooding Incident at the Ågesta Pressurized Heavy Water Nuclear Power Plant
This report is a Master's thesis in Nuclear Reactor Engineering to be submitted to the SKi (Swedish Nuclear Power Inspectorate). The work has been performed at the Division of Nuclear Power Safety, KTH,Stockholm. It is an independent investigation of the consequences of the flooding incident at the Agesta HPWR, in Stockholm, Sweden, which occurred on the 1st of May 1969. The issue was raised...
Content type: Publications