Filtered generated 217 hits.
-
2007:04 Link Between RI-ISI and Inspection Qualification: Relationship between Defect Detection Rate and Margin of Detection
A relationship has been established between defect detection ratio and margin of detection based on blind trails. The results are based on a rather small amount of data produced by personnel from one inspection laboratory but give us indications of how signal to noise ratio is possible to relate to the probability of detection (POD) used in RI-ISI models. The relationship need to be developed...
Content type: Publications -
2007:14 Review of experimental data for modelling LWR fuel cladding behaviour under loss of coolant accident conditions
This project has contributed to the research goal of giving a basis for SKIs supervision by means of evaluating experimental data and modelling the nuclear fuel cladding during a design base accident. The project has also contributed to the research goal to develop the competence about licensing of fuel at high burnup, which is an important safety issue. The results are useful as such, but...
Content type: Publications -
2011:19 Experimental evaluation of influence from residual stresses on crack initiation and ductile crack growth at high primary loads
Cracked components are usually subjected to loads causing both primary and secondary stresses, e.g. welding components. Engineering assessment approaches, such as the ASME XI code and the R6 procedure, are commonly used to conduct integrity assessment of such components. There has been an ongoing debate how to treat secondary stresses using engineering assessment methods. The nature of these...
Content type: Publications -
2011:29 Research and Development Program in Reactor Diagnostics and Monitoring with Neutron Noise Methods, Stage 17
This report constitutes Stage 17 of a long-term research and development program concerning the development of diagnostics and monitoring methods for nuclear reactors. Results up to Stage 16 were reported in SKI and SSM reports, as listed below and in the Summary. The results have also been published in international journals and have been included in both licentiate- and doctor’s degrees.
Content type: Publications -
2012:07 Implementation of the Master Curve method in ProSACC
Cleavage fracture toughness data display normally large amount of statistical scatter in the transition region. The cleavage toughness data in this region is specimen size-dependent, and should be treated statistically rather than deterministically. The Master Curve (MC) methodology is a procedure for mechanical testing and statistical analysis of fracture toughness of ferritic steels in the...
Content type: Publications -
2011:33 Mathematical modelling of ultrasonic testing of components with defects close to a non-planar surface
The report describes work that has been performed in order to model ultrasonic testing of components that contain a defect close to a non-planar surface. The studies have been performed in both 2D and 3D, and in 2D in both the anti-plane (SH) and the in-plane (P-SV). The results show that the presence of a non-planar back wall can reduce the detectability of defects close to the surface. The...
Content type: Publications -
2009:15 Improvement and Validation of Weld Residual Stress Modelling Procedure
Weld residual stresses have a large influence on the behavior of cracks growing under normal operation loads and on the leakage-flow from a through-wall crack. Accurate prediction of these events is important in order to arrive at proper conclusions when assessing detected flaws, for inspection planning and for assessment of leak-before-break margins. Therefore, it is very important to have...
Content type: Publications -
2009:07 Dependency Analysis Guidance Nordic/German Working Group on Common Cause Failure analysis
The Regulatory Code SSMFS 2008:1 of Swedish Radiation Safety Authority (SSM) includes requirements regarding the performance of probabilistic safety assessments (PSA), as well as PSA activities in general. Therefore, the follow-up of these activities is part of the inspection tasks of SSM. According to the SSMFS 2008:1, the safety analyses shall be based on a systematic identification and...
Content type: Publications -
2009:27 Analysis Strategy for Fracture Assessment of Defects in Ductile Materials
SSM has supported research for investigating the role of secondary stresses when fracture assessments are performed for cracked structures made of ductile materials. There are evidences that indicate that some secondary stresses, such as weld residual stresses, are not as important as primary stresses for estimating the safety margin against rupture (measured by the J-integral) for the type...
Content type: Publications -
2010:46 Development of the PRO-LOCA Probabilistic Fracture Mechanics Code, MERIT Final Report
The MERIT project has been an internationally financed program with the main purpose of developing probabilistic models for piping failure of nuclear components and to include these models in a probabilistic code named PRO-LOCA. The principal objective of the project has been to develop probabilistic models for piping failure of nuclear components and to include these models in a...
Content type: Publications