Din avgränsning ger 301 träffar.
-
2009:15 Improvement and Validation of Weld Residual Stress Modelling Procedure
Weld residual stresses have a large influence on the behavior of cracks growing under normal operation loads and on the leakage-flow from a through-wall crack. Accurate prediction of these events is important in order to arrive at proper conclusions when assessing detected flaws, for inspection planning and for assessment of leak-before-break margins. Therefore, it is very important to have...
Innehållstyp: Publikationer -
2009:10 Regleringen av matarvattenflödet i en BWR. Med exempel från Forsmark 2
Säkerheten i kärntekniska anläggningar ska upprätthållas genom att radiologiska olyckor förebyggs. I reaktorer sker detta genom att det finns flerfaldiga barriärer och ett så kallat djupförsvar. I djupförsvaret ingår att åtgärder vidtas för att tillförsäkra lugn och störningsfri drift utan transienter som kan...
Innehållstyp: Publikationer -
2009:26 Tillämpning av stabil spricktillväxt vid brottmekanisk bedömning av defekter i sega material
Vid brottmekaniska analyser studeras i huvudsak haverimekanismerna sprött brott och plastisk kollaps samt kombinationen av dessa. Den styrande mekanismen bestäms av komponentens materialegenskaper, styrande belastning och defektens geometri. Proceduren enligt SKI-rapport 99:49 är idag en av de mest använda metoderna vid brottmekaniska analyser. Proceduren som baseras på...
Innehållstyp: Publikationer -
2009:27 Analysis Strategy for Fracture Assessment of Defects in Ductile Materials
SSM has supported research for investigating the role of secondary stresses when fracture assessments are performed for cracked structures made of ductile materials. There are evidences that indicate that some secondary stresses, such as weld residual stresses, are not as important as primary stresses for estimating the safety margin against rupture (measured by the J-integral) for the type...
Innehållstyp: Publikationer -
2007:41 Dependency Analysis Guidence, Nordic/German Working Group on Common cause Failure analysis Phaase 1 project report: Comparison and application to test cases
The report “Nordic/German Working Group on Common cause Failure analysis. Phase 1 project report: Comparisons and application to test cases” presents a common attempt by the authorities and the utilities to create a methodology and experience base for defence and analysis of dependent failures. The performed benchmark application has shown that how the data is interpreted is of significant...
Innehållstyp: Publikationer -
2007:27 Kompetensöverföring på svenska kärnkraftverk i samband med pensionsavgångar
Rapporten visar att ett av Sveriges tre kärnkraftverk har ett program för kompetensöverföring. På de två som saknar program efterfrågas mer struktur inom området, även om man redan nu arbetar med mentorer eller handledare. Genomgående är upplevelsen av bristen på resurser för överrekrytering och tiden till att överföra.
Innehållstyp: Publikationer -
2007:39 Influence of Crack Morphology on Leak Before Break Margins
The SKI regulation SKIFS 2004:2 allows for the use of Leak Before Break (LBB) as one way to provide assurance that adequate protection exists against the local dynamic consequences of a pipe break. The way to demonstrate that LBB prevails relies on a deterministic procedure for which a leakage crack is postulated in certain sections of the pipe based on the leak detection capability of the...
Innehållstyp: Publikationer -
2007:37 Identification of Common Cause Initiating Events Using the NEA IRS Database
The study carried out within the framework of this project is a continuation of work conducted for SKI in 1998 on the identification of Common Cause Initiators based on operational events documented in the NEA Incident Reporting System (IRS). This project covered the events reported in the IRS database with the incident date in the period of 1980- 01-01 – 2006-11-15. The events of highest...
Innehållstyp: Publikationer -
2007:24 Safety Management in Non-Nuclear Contexts Examples from Swedish Railway Regulatory and Company Perspectives
The authors describe important features of safety management and the results are modelled according to the systems perspective developed. These are definitions of safety management, the structure of the organizations, organizational change, regulatory and operational activities, safety strategy, threats to safety, information management and feedback, incident and accident reporting, and...
Innehållstyp: Publikationer -
2007:42 Regleringen av matarvattenflödet i en PWR - Med exempel från Ringhals 3
Rapporten ger en redovisning av kända och potentiella problem med matarvatten- regleringen i tryckvattenreaktorer, problem som i vissa fall förekommit tidigare internationellt. Vidare ges en detaljerad beskrivning av matarvattenregleringen vid Ringhals 3, som kan sägas vara representativ även för övriga svenska tryckvatten- reaktorer. Analysresultaten visar att R3:s...
Innehållstyp: Publikationer